cat.8100v keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. then, there shall be found no remarkable abnormality on the capacitor terminals. after applying the pressure load of 5n for 101 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. after 2000 hours' application of rated voltage at 85 ? c , or derated voltage at 125 ? c , capacitors meet the characteristic requirements listed below. capacitance change within 10% of initial value dissipation factor initial specified value or less leakage current initial specified value or less after application of surge in series with a 33 ? resistor at the rate of 30 seconds on, 30 seconds off, for 1000 successive test cycles at 85 ? c , capacitors meet the characteristics requirements listed below. capacitance change within 5% of initial value dissipation factor initial specified value or less leakage current initial specified value or less at 40 ? c , 90~95% r.h., for 500 hours (no voltage applied) capacitance change within 10% of initial value dissipation factor initial specified value or less leakage current initial specified value or less +15% max. (at +125 ? c ) +10% max. (at +85 ? c ) --10% max. (at --55 ? c ) after 1 minute's application of rated voltage, leakage current at 20 ? c is not more than 0.01cv or 0.5a, whichever is greater. after 1 minute's application of rated voltage, leakage current at 85 ? c is not more than 0.1cv or 5a, whichever is greater. after 1 minute's application of derated voltage, leakage current at 125 ? cis not more than 0.125cv or 6.3a, whichever is greater. 33~68f 6%max. 100f~ 8%max. 150f 10%max. 220f~330f 12%max. esr (100khz) leakage current 33f 0.90 ? 47f 0.80 ? 68f 0.75 ? 100f~ 0.70 ? ~150f 0.22 ? ~ 220f 0.20 ? ~ 330f 0.15 ? ~ 470~1500f 0.12 ? ~ 2200f 0.07 ? 5n (0.51kg f) for 10 1 seconds solid tantalum electrolytic capacitors f75 maximum cv conformal coated chip f72 low profile conformal coated chip specifications type numbering system (example : 16v 150 f) drawing item category temperature range capacitance tolerance dissipation factor (120hz) capacitance change by temperature damp heat temperature cycles resistance to soldering heat surge ? endurance ? shear test terminal strength per formance characteristics --55 ~ + 125 ? c (rated temperature : + 85 ? c ) 20%, 10% (at 120hz) f72 f75 68~330f 10%max. 470f 14%max. 680f 18%max. 1000f 24%max. 1500f 30%max. 2200f 45%max. reflow at 260 ? c for 10 seconds , dipping flow at 260 ? c for 10 seconds capacitance change within 5% of initial value dissipation factor initial specified value or less leakage current initial specified value or less at -- 55 ? c / +125 ? c , 30 minutes each, for 5 cycles, capacitance change within 5% of initial value dissipation factor initial specified value or less leakage currentv initial specified value or less r230 45 45 20 1 mm type numbering system (example : 10v 100f) drawing dimensions dimensions standard ratings l w h d b a l w b a h d solder electrode (mm) d dimension only for reference f75 f72 ? as for the surge and derated voltage at 125 ? c , refer to page 266 for details. f75 0 33 0 47 0 68 100 150 220 330 336 476 686 107 157 227 337 r r r r r r r r r r r r r r (r) r r r 4 6.3 10 16 0g 0j 1a 1c v f72 code 0 68 100 150 220 330 470 680 1000 1500 2200 686 107 157 227 337 477 687 108 158 228 c c d d d r r r c c d d d r r c c d d r c c d r 4 6.3 10 16 0g 0j 1a 1c v code case code lwhab(d) d 7.3 0.3 4.3 0.3 2.8 0.3 1.3 0.4 3.9 0.6 (6.4) r 7.2 0.3 6.0 0.3 3.5 0.3 1.3 0.4 3.8 0.6 (6.2) (mm) d dimension only for reference c 7.1 0.3 3.2 0.3 2.5 0.3 1.3 0.3 3.6 0.6 (6.0) cap.( f) cap. ( f) case code lwhab(d) r 7.2 0.3 6.0 0.3 1.2 0.3 1.3 0.4 3.8 0.6 (6.2) taping code (refer to page 267 for details) f 1 7 2 2 3 1 4 a 5 1 6 0 7 7 8 m 9 r 10 11 case code capacitance tolerance rated capacitance rated voltage series taping code (refer to page 267 for details) f 1 7 2 5 3 1 4 c 5 1 6 5 7 7 8 m 9 d 10 11 case code capacitance tolerance rated capacitance rated voltage series adapted to the rohs directive (2002/95/ec).
|
